Artemmka`s Xedos 6 2.5 V6 KL. Riga

[born2die]

Zitat von w00lf

Glaub eher das sind LEDs aber ich warte mal auf eine Antwort. Sieht hammer geil aus.

mfg, Wolfgang

das ist Xenon die haben da alles überall Xenon verbaut nur wir dürfen sowas nicht

[Rooz21]

Zitat von born2die

das ist Xenon die haben da alles überall Xenon verbaut nur wir dürfen sowas nicht

ja da sagste was... leider

@ w00lf: tippe 100% auf xenon, weil guck dir mal die refkletion aufn boden an

PS: wär aber vieeeeeeeel zu auffällig, xenon als abblendlicht sowie als nebler gleichzeitig

[Artemmka]

Zitat von Rooz21

... you are using FK lower springs, I've got the same but my car isn't so low as yours. are you satisfied with them springs?

Yes, i`m fully satisfied, but i thought that it will be much lower, when i compare old spring with new one (you can see on picture difference). I like it more, because the vibration is gone away (i had low vibration when acalarating at 2300-2700rpm). Perfect look!

Zitat von w00lf

Hey, very nice.
Which bulbs did you use in this picture?

It`s not a Xenon, it`s just Philips Blue vision H3 It looks different in different angle.
I use fog lamps only for day running lights. I have Xenon 6000K in main lights H1.
But i plan to put Xenon in fog too in future.

[Artemmka]

Gkiokan
Swap was made in service. But i regularly was there and looking and helping.
After the swap was made i spent a lot of money and time to make all to the end.
I`ll add new post about swap in few days. I`ll write everything what i have made during swapping.
I had 215x45x17, now i put 205x50x17
The alloys rims of M6 are very heavy, on 205x50 it`s better running, but i need to control spinning.
I thought on your idea, but you right, not so insane power added during swap
Sure, safety first, then other things.

[Artemmka]

I WOULD LIKE TO SAY THANK YOU TO ALL COMMENTS!
THANK YOU FOR ALL RESPECT!

P.S. sorry that i use english language on your forum

[w00lf]

Zitat von Artemmka

It`s not a Xenon, it`s just Philips Blue vision H3 It looks different in different angle.
I use fog lamps only for day running lights. I have Xenon 6000K in main lights H1.
But i plan to put Xenon in fog too in future.

Are you serious? My Bluevision looked so much yellower than yours, unbelievable.... So i put in the Osram Nightbreaker again, they are a little bit more "white" (at least at night).

Zitat von Artemmka

P.S. sorry that i use english language on your forum

No problem. Sorry for writing in german on your thread. It was just a discussion wheter you put in Xenon or LEDs.

mfg, Wolfgang

[Artemmka]

w00lf
Maybe on the photo it looks so bright and white.
In real life it`s not white!
When i bought i thought that it will look better.

But you know, that i put the same mine Philips H3 in Mitsubishi Galant, it looks really white.
I think the problem is that we have Lens there.

[Artemmka]

Engine from: Mazda 626 2.5 V6 1993 (automatic)
Inject manifold and throttle body from 626 2.5 too.
ECU: KL05
Airflow meter: KL02
Wiring is mine KF (stock)
I have 1-th generation X6 and the engine was from 626 of 1-th generation too.
So all sensors are in place.
Put my 2.0 KF manual transmission.
Drive shafts were from X6 KF. Now i put of 626 2.5 automatic (i thought that from KL they are larger, but they are the same)
Rear engine mounting is new, from 2.5 engine (it`s larger)
New clutch and bearing.
Changed rods, oil seals, gaskets of valve cover, new water pump, new tensioner, new timing belt, all rolls, new oil, filters, NGK wires, denso spark plugs.
I made everything in service, only swap and engine preparing.
After that spend a lot of time on other things, cleaning, putting everything in correct place.
Here are some photos.

[Artemmka]

The door panels are made by myself. I spent 4 evenings.
Handles are from Xedos 9 2001 year.

[w00lf]

Wow, looks pretty nice.
Especially those door handles. Where did you get them?

regards, Wolfgang